例句與造句

1. Continuous casting process
   連續鑄造法
2. Breakout is the most catastrophic incident in the continuous casting process
   在連鑄生產過程發生的各類事故中，損害最嚴重的便是漏鋼事故。
3. Molten steel level in mould of continuous cast process and casting speed can directly effect temperature of molten steel in mould
   摘要結晶器液位和鑄坯拉速可直接影響結晶器內鋼液溫度。
4. According to the analysis of dynamic scheduling for steelmaking - continuous casting process , a dynamic scheduling model based on just - in - time principle is formulated
   摘要通過對煉鋼連鑄生產動態調度問題的分析，建立了基于準時制思想的煉鋼連鑄生產動態調度模型。
5. When the data of logistics in current process are used for input of simulating logistics in future 100 % continuous casting process , supply of hot metal from iron - making process may not satisfy the needs of 100 % continuous casting on raw materials . because planning scheme in continuous casting process depends greatly on smelting scheme in convertor vessel , it is important for operator to balance raw materials supply , smelting and casting in order to realize the scheme of 100 % continuous casting . when some equipment are work abnormally , mixer of hot metal and lf furnace can be used for logistics buffer
   用攀鋼煉鋼生產數據對仿真軟件系統進行的測試和仿真研究結果表明：仿真系統的隨機數發生算法可以實現對作業時間的依分布隨機抽取；在相似的輸入條件下，仿真結果與實際生產物流的時間分布規律基本吻合，達到了仿真軟件設計的預期目標；若以攀鋼提釩煉鋼廠現工藝的鐵水輸入作為全連鑄后的輸入條件，則現工藝的物料供應能力可能難以滿足全連鑄生產的要求；連鑄機的連澆計劃對轉爐爐次計劃的編制有很高的要求，合理安排來料、煉鋼與澆鑄三者間的物流平衡關系將是保證全連鑄作業的重要條件；當出現設備異常情況時，可以利用混鐵爐與lf爐站前等待作為物流緩沖池，通過延長系統的平均物流時間來緩解因設備檢修和故障等擾動所造成的影響，確保生產的順利進行。
6. It's difficult to find continuous casting process in a sentence. 用continuous casting process造句挺難的
7. The control system of mould level is crucial to improve the slab quality in the continuous casting process , pid controller is used in the traditional mould level control , and it has some defaults , such as : at the start - up or finishing period of casting or during the changeover of tundish , pid control has a bad effect , its overshoot is large and its transient time is long ; the erosion of the tundish stopper and the submersed nozzles lead to the accuracy of control become bad ; the abrupt falloff of block in the submersed nozzles makes the level acutely fluctuate , and pid control can not overcome the disturbances resulted from the change of casting speed
   結晶器液位控制系統是提高連鑄產品質量的關鍵環節，傳統的連鑄機液位控制方法采用常規的pid控制，存在如下不足：開始、結束澆注和換中間罐澆注時，控制效果差，超調量大，過渡時間長；塞棒頭和浸入式水口被腐蝕后引起控制精度差；浸入式水口堵塞物的突然脫落所引起的液位劇烈波動；無法克服拉速波動引起的擾動。